1. CNC MILLING & ROUTING

CNC Milling & Routing

We fixture parts on 3–5 axis machining centers and CNC lathes, programming optimal toolpaths with CAM. Tolerances and surface finish targets are secured through the right tools, coatings and coolant strategy for each material. First Article Inspection (FAI) is issued on the pilot piece; Statistical Process Control (SPC) keeps serial production stable. Critical dimensions are verified with CMM, profile projectors and calibrated gauges.

2. HYDRAULIC & ECCENTRIC PRESS FORMING

Hydraulic & Eccentric Press Forming

For cutting, drawing and forming we design tooling and calculate press tonnage to match the material and geometry. Lubrication, strip feeding and scrap removal devices secure cycle reliability. Springback and die wear are monitored with angle gauges and preventive maintenance. Dimensional approval is granted on first-off parts; production follows control cards.

3. INDUSTRIAL POWER TRANSMISSION

Industrial Power Transmission Systems (Conveyors & Chains)

We engineer conveyors and chain drives by calculating load, speed and service factors to select pitch, materials and sprockets. Lubrication, tensioning and guarding reduce downtime and raise safety. Commissioning includes alignment and tension checks; we hand over a maintenance plan and spare set. Designs comply with ISO/DIN and sector needs such as hygiene and noise control.

4. LASER CUTTING & PRESS BRAKE BENDING

Laser Cutting & Press Brake Bending

Nesting and kerf compensation boost material yield and edge quality. On bending, K-factor, bend radius and springback are tuned to thickness and alloy. First-off angle and burr checks are performed; serial production follows control sheets. Proper pre/post surface treatments keep flatness and edge finish consistent.

5. MOLD & TOOLING

Mold & Tooling Production

We design molds, fixtures and gauges with DFM/DFA principles, selecting the right tool steel and heat treatment. Precision is reached via machining plus EDM/wire-cut and closed with fast trial–improvement loops. We manage the life cycle with measurement reports, maintenance plans and spare kits. Fixture repeatability is validated by CMM and dedicated gauges during production.

6. PANEL CUTTING & EDGE BANDING

Panel Cutting & Edge Banding

We secure accuracy and perpendicularity with the right blades and feed parameters. In edge banding, adhesive type (hot-melt/PU) and the heat–pressure–speed trio deliver strong bonding. Corners, chamfers and surface cleaning are verified at final inspection. Barcode/lot tracking keeps batches fully traceable.

7. PLASTIC INJECTION MOLDING

Plastic Injection Molding

We define the process window with proper material drying and temperature profiles, then release with a first-off approval. Color/lot traceability, dimensional checks and visual quality are monitored during serial runs. In-mold sensors can track fill behavior and trigger warnings on parameter drift. The goal is repeatable cycles with minimal scrap.

8. SURFACE TREATMENT & PAINTING

Surface Treatment & Painting

Surface preparation—blasting or chemical pretreatments—is tailored to the substrate. Coating/paint thickness is measured; adhesion (cross-cut) and curing profiles are checked. Corrosion resistance is achieved with the right primer/topcoat combination. Visual and functional requirements are locked in a control plan.

9. THERMOFORMING

Thermoforming

We balance material distribution using zoned heating and mold/plug settings. Vacuum level and cycle time are logged for stable production. Trim dies secure dimensional accuracy; templates and gauges enable fast checks. The result is light, economical parts with consistent appearance and rigidity.

10. VULCANIZATION

Vulcanization

For rubber and elastomers we lock mechanical properties with controlled temperature–time–pressure recipes. Mold venting and flash control define final quality. Shore hardness, tensile/elongation and adhesion tests release each batch. Post-cure and measurement plans are applied when required.

11. WELDING & ASSEMBLY

Welding & Assembly

We weld MIG/MAG, TIG and spot per WPS, controlling distortion with fixtures. Visual tests (VT) and, when needed, MT/PT confirm weld integrity. Assembly uses specified torque values and functional tests recorded on route cards. For repeatability we run control plans and Poka-Yoke solutions on the line.

12. WIRE & SHEET BENDING

Wire & Sheet Bending

On CNC wire benders and press brakes we compensate springback to hit the target angle. Radius, hole-to-edge distance and clash risks are verified before production. Go/No-Go gauges and angle meters control serial parts. Protective films/pads keep surfaces clean and scratch-free.